How To Replace A Bathtub (For Newbies).
How To Replace A Bathtub (For Newbies).
Blog Article
They are making several good observations regarding How to Install a Bathtub Yourself overall in this post just below.
Setting up a bath tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult project. If the old tub is easily easily accessible, the job can relocate immediately; if you have to open up a wall surface to eliminate the old bathtub and also place the brand-new bath tub, the job is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to vacate the old bathtub and also embeded in the new one. Ensure you have qualified yourself for the work and also fit attempting it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to think about utilizing one before you start. Opportunities are you might need a professional plumber to make tube links.
This post will assist you install a new bathtub in your washroom if you have actually currently purchased a new tub and do not require to alter the plan of your previous water pipelines.
Your devices as well as material checklist should consist of the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place in between the faucet as well as the sink. Safeguard the tap in place with the supplier provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous kind ought to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the tub in the called for position. The wood boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost flexible tap adapter to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water system and also check all joints and brand-new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally examine the overflow outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been used a minimum of once as this will certainly resolve it right into its last position.
Preparing for the Installation
Firstly, the supporting frame supplied with the bath ought to be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its final position.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub is in use. The sealer can fracture rather early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about How to Install a Bathtub Yourself? Put feedback directly below. We would be delighted to listen to your ideas about this post. We are looking forward to see you back again in the near future. Enjoyed our write-up? Please share it. Let someone else check it out. We truly appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Schedule An Appointment Report this page